Daewoo lanos engine diagram?
Q. i need to know where the inlet air temp sensor is... IAT also the engine coolant temp sensor... ECT any help is greatful
Asked by kantsas - Mon Jul 23 11:29:22 2007 - - 1 Answers - 0 Comments
A. I have found that autozone.com is very helpful with finding component locations...if they have your make & model in their system...go to their site & start by putting in your make & model and check it out!
Answered by dadmizer999 - Mon Jul 23 11:37:14 2007
Q. i need to know where the inlet air temp sensor is... IAT also the engine coolant temp sensor... ECT any help is greatful
Asked by kantsas - Mon Jul 23 11:29:22 2007 - - 1 Answers - 0 Comments
A. I have found that autozone.com is very helpful with finding component locations...if they have your make & model in their system...go to their site & start by putting in your make & model and check it out!
Answered by dadmizer999 - Mon Jul 23 11:37:14 2007
i need a timing belt diagram for a 99 daewoo laganza with a 2.2 engine can any one help me please?
Q. i need a timing belt diagram for a 99 daewoo laganza with a 2.2 engine can any one help me please?
Asked by blueeyedplayboy2004 - Sat May 13 11:44:03 2006 - - 2 Answers - 0 Comments
A. Make sure you do this right cause it is a interference engine!!! Listen to me only and I will walk you through it. Also you can e-mail me if you have questions. 1. Align the timing mark on the crankshaft gear with the notch on the bottom of the rear timing belt cover. 2. Align the timing mark on the camshaft gears using the intake gear mark for the intake gear and the exhaust gear mark for the exhaust gear. 3. Turn the hex-hey tab in a counterclockwise direction to tension the belt. Turn until the pointer aligns with the notch. This is above the crank pulley if you didn't know. 4. Once all is on turn the crank 2 full turns and then check to make sure all marks are still aligned and then you are good. Good luck.
Answered by Todd G - Sat May 13 12:06:08 2006
Q. i need a timing belt diagram for a 99 daewoo laganza with a 2.2 engine can any one help me please?
Asked by blueeyedplayboy2004 - Sat May 13 11:44:03 2006 - - 2 Answers - 0 Comments
A. Make sure you do this right cause it is a interference engine!!! Listen to me only and I will walk you through it. Also you can e-mail me if you have questions. 1. Align the timing mark on the crankshaft gear with the notch on the bottom of the rear timing belt cover. 2. Align the timing mark on the camshaft gears using the intake gear mark for the intake gear and the exhaust gear mark for the exhaust gear. 3. Turn the hex-hey tab in a counterclockwise direction to tension the belt. Turn until the pointer aligns with the notch. This is above the crank pulley if you didn't know. 4. Once all is on turn the crank 2 full turns and then check to make sure all marks are still aligned and then you are good. Good luck.
Answered by Todd G - Sat May 13 12:06:08 2006
I need a timing belt diagram, for 1998 daewoo nubira, 1.6lite 16v twin cam.?
Q. had mechanic replace timing belt, now no compression in all cylinders. Mechanic told me all valves in hed must be bent. hoping to find a diagram or engine manual for this car. dont know engine name?? thankyou
Asked by auzzi_17 - Sun Apr 1 23:50:42 2007 - - 2 Answers - 0 Comments
A. run a compression test
Answered by smokey - Sun Apr 1 23:56:16 2007
Q. had mechanic replace timing belt, now no compression in all cylinders. Mechanic told me all valves in hed must be bent. hoping to find a diagram or engine manual for this car. dont know engine name?? thankyou
Asked by auzzi_17 - Sun Apr 1 23:50:42 2007 - - 2 Answers - 0 Comments
A. run a compression test
Answered by smokey - Sun Apr 1 23:56:16 2007
From Yahoo Answer Search: 'DAEWOO ENGINE diagram'
Fri Jan 1 12:38:19 2010 [ refresh local cache ]
